Air Plasma Cutting Machine in Odisha

Air Plasma Cutting Machine in Odisha

  • Home
  • >
  • Air Plasma Cutting Machine in Odisha
💨 Runs on Compressed Air | No Gas Cylinders | 70% Lower Cost

Air Plasma Cutting Machine in Odisha

Lowest Operating Cost | Perfect for Small Workshops & Job Work | Serving Rourkela, Bhubaneswar, Cuttack, Angul, Jharsuguda

Looking for an air plasma cutting machine in Odisha that won't burn a hole in your pocket? Shri Shyam Engg Works brings you compressed air plasma cutters – no expensive oxygen, no nitrogen cylinders. Just connect your workshop compressor and start cutting. Perfect for small fabrication units, gate making workshops, steel plant ancillaries, and job work centers in Odisha – including Rourkela (Steel City), Bhubaneswar, Cuttack, Angul, Jharsuguda, Sambalpur, Kalinganagar, Talcher, Dhenkanal, Balasore, Berhampur, Paradeep, Jajpur, Keonjhar, Sundargarh and all across the state.

70%
Lower Operating Cost
0
Gas Cylinders Needed
6-25mm
Cutting Capacity
1.5L
Air Consumption/min

What Makes Air Plasma Different?

Traditional plasma cutters need expensive gases like oxygen or nitrogen. Air plasma cutting machine uses shop compressed air – same air your pneumatic tools use. The air is compressed, dried, and fed directly to the plasma torch. That's it.

💰 Cost Comparison – Air Plasma vs Gas Plasma (Per 8 Hour Shift)

🔵 Air Plasma (Compressed Air)₹0 – No gas cost
🟠 Gas Plasma (Oxygen/Nitrogen)₹1,500 – ₹2,500 per shift
🟢 Your Monthly Savings₹30,000 – ₹50,000

Key Features of Our Air Plasma Cutting Machine

💨 Compressed Air Operated

No gas cylinders, no refilling hassle. Runs on 60-100 PSI shop air.

⚡ High-Frequency Start

Non-high frequency start – no interference with CNC controller.

🔧 Built-In Air Filter

Moisture separator + air dryer included for clean dry air.

📱 Digital Display

Real-time current, air pressure, and fault diagnosis.

🛡️ Overload Protection

Automatic shutdown on voltage fluctuation or overheating.

🎮 CNC Ready Interface

Standard CPC port – connect to any CNC or handheld use.

What Can You Cut with Air Plasma in Odisha?

🔘 Mild Steel

Up to 25mm clean cut, 30mm severance cut

✨ Stainless Steel

Up to 20mm with nice finish

🔘 Aluminum

Up to 18mm, no dross on thin sheets

🟡 Copper & Brass

Up to 12mm for electrical components

📀 Galvanized Sheets

No toxic fumes like oxy fuel

Perfect for Odisha's Small Workshops & Steel Plants

🏪 Gate & Railing Makers

Cut decorative patterns, arch designs, and nameplates without expensive tooling.

🔩 Job Work Centers

Take plasma cutting contracts – low investment, quick returns.

🚗 Auto Repair Shops

Cut chassis parts, brackets, and repair patches on demand.

🏭 Steel Plant Maintenance

Perfect for maintenance crews in Rourkela Steel Plant, Kalinganagar, and Angul – cut and repair on the spot.

🏠 Home Fabricators

Portable units available – take it to site for installation work.

⛏️ Mining Equipment Repair

Repair and cut mining equipment parts in Keonjhar, Sundargarh, and Mayurbhanj.

Technical Specifications – Air Plasma Range

40 Amp Air PlasmaCuts up to 12mm mild steel
60 Amp Air PlasmaCuts up to 20mm | Best for general fabrication
100 Amp Air PlasmaCuts up to 25mm | Heavy job work, steel plant maintenance
120 Amp Air PlasmaCuts up to 30mm | Thick plate cutting
Air requirement5-8 CFM at 70-90 PSI
Duty cycle60% at full load | 100% at lower amps

📍 We Serve These Industrial Areas in Odisha

Rourkela Bhubaneswar Cuttack Angul Jharsuguda Sambalpur Kalinganagar Talcher Dhenkanal Balasore Berhampur Paradeep Jajpur Keonjhar Sundargarh Mayurbhanj Rayagada Koraput

✅ Free delivery to Odisha | ✅ Demo available | ✅ Spare parts pan-India delivery

Frequently Asked Questions – Odisha Customers

Q: What compressor do I need for air plasma?
A: A 2HP or 3HP compressor with 5-8 CFM at 70-90 PSI is sufficient. We also sell small silent compressors if needed.
Q: Is air plasma good for stainless steel?
A: Yes, air plasma cuts stainless steel very well. For mirror finish, you may want nitrogen, but air gives good clean cuts.
Q: What is the warranty?
A: 1 year on plasma source + 6 months on torch.
Q: Can I use air plasma with my CNC table?
A: Yes, all our air plasma units have CPC port – plug and play with any CNC controller.
Q: Do you provide installation?
A: Yes, we can send our engineer for installation and training. Small units also have video support.
Q: Is there service support in Odisha?
A: Yes, we have dedicated service engineers for Rourkela, Bhubaneswar, Cuttack, Angul, Jharsuguda, and all Odisha.
Q: Is this suitable for steel plant maintenance?
A: Absolutely. Our 80A and 100A models are perfect for maintenance work in Rourkela Steel Plant, Kalinganagar, and Angul.

Why Shri Shyam Engg Works for Air Plasma in Odisha?

🔌 Complete Package

Air plasma source + torch + consumables + air filter unit – everything included.

🧪 Demo on Your Material

Bring your sheet to our Faridabad factory or ask for on-site demo in Odisha.

📦 Consumables in Stock

Electrodes, nozzles, swirl rings – always available.

🔧 1 Year Warranty

Full warranty on plasma source + 6 months on torch.

📞 Phone Support

WhatsApp video call support for troubleshooting.

💰 EMI Options

Low-cost financing available for small workshop owners.

Get Best Price – Air Plasma in Odisha

Tell us your cutting thickness and budget – we have the right air plasma for you.

⭐ Lowest price air plasma cutter in Odisha | EMI available | Free installation